Chapter 07 Exam Preparation: Field Effect Transistors (FET)
Course: Electrical and Electronic Circuit (EEC) Course Code: 510203 Chapter: 07 — Field Effect Transistors Purpose: Beginner-friendly revision, exam-ready answers, formulas and solved numerical practice.
1. What to prepare
Prioritise these syllabus areas:
- Classification of FET: JFET and MOSFET.
- Construction and operation of N-channel and P-channel JFET.
- JFET drain and transfer characteristics.
- Pinch-off, cutoff and operating regions.
- MOSFET construction, operation and characteristics.
- Enhancement-mode and depletion-mode MOSFET.
- DC biasing of JFET, especially self-bias.
- Shockley's equation and basic JFET bias numericals.
Answer-writing structure: definition → labelled diagram → construction → working → characteristics/formula → application or comparison.
-
\(I_D\) = drain current
-
\(V_{GS}\) = gate-to-source voltage
2. Essential definitions (exam-ready)
Field Effect Transistor (FET): A FET is a three-terminal semiconductor device in which an electric field produced by the gate voltage controls current flowing through a channel between source and drain.
Channel: The conducting path through which current flows between the source and drain terminals.
Gate: The terminal that controls channel conductivity by applying an electric field.
Source: The terminal through which majority carriers enter the channel.
Drain: The terminal through which majority carriers leave the channel.
JFET: A Junction Field Effect Transistor is a voltage-controlled device in which a reverse-biased P-N junction at the gate controls current through the channel.
MOSFET: A Metal-Oxide-Semiconductor Field Effect Transistor is a FET whose gate is electrically insulated from the semiconductor channel by a thin insulating layer.
Pinch-off: In a JFET, pinch-off is the condition at which the channel becomes sufficiently constricted near the drain that drain current becomes approximately constant for a fixed gate voltage.
Cutoff: The operating condition in which the channel current becomes approximately zero.
Biasing: The application of suitable DC voltages to establish a desired no-signal operating point (Q-point).
3. Classification of FET
FETs are mainly divided into two types:
- JFET (Junction Field Effect Transistor)
- MOSFET (Metal-Oxide-Semiconductor Field Effect Transistor)
JFET types: - N-channel JFET - P-channel JFET
MOSFET types: - Enhancement-mode MOSFET - Depletion-mode MOSFET
Each MOSFET mode may be N-channel or P-channel.
4. BJT vs FET
| Feature | BJT | FET |
|---|---|---|
| Full form | Bipolar Junction Transistor | Field Effect Transistor |
| Charge carriers | Both electrons and holes participate | Mainly one majority-carrier type in the channel |
| Control | Base current controls collector current in the usual model | Gate voltage controls channel current |
| Input current | Requires base current | Gate current is very small in normal operation |
| Input resistance | Generally lower | Generally high |
| Description | Current-controlled device | Voltage-controlled device |
| Terminals | Emitter, base, collector | Gate, source, drain |
Exam point: BJT is called bipolar because both electrons and holes participate in conduction. FET is called unipolar because channel conduction is mainly due to one type of majority carrier.
5. JFET construction and operation
N-channel JFET construction
An N-channel JFET consists of an N-type semiconductor bar forming the channel. Two P-type regions are formed on opposite sides of this channel and connected together to form the gate. The two ends of the channel form the source and drain terminals.
- Majority carriers: electrons.
- Gate-channel junction: normally reverse biased.
- Gate current: very small in normal operation.
P-channel JFET construction
A P-channel JFET has a P-type channel and N-type gate regions.
- Majority carriers: holes.
- Voltage polarities are opposite to those used for an N-channel JFET.
- Gate-channel junction is normally reverse biased.
Working of N-channel JFET
- The drain is made positive relative to the source.
- Electrons enter the channel through the source and move towards the drain.
- The gate-channel P-N junction is reverse biased.
- Making gate-to-source voltage \(V_{GS}\) more negative widens the depletion regions.
- The channel becomes narrower and drain current \(I_D\) decreases.
Important terms:
| Symbol | Meaning |
|---|---|
| \(V_{GS}\) | Gate-to-source voltage |
| \(V_{DS}\) | Drain-to-source voltage |
| \(I_D\) | Drain current |
| \(I_{DSS}\) | Drain current at \(V_{GS}=0\) in the specified saturation condition |
| \(V_{GS(off)}\) | Gate-to-source cutoff voltage |
For the usual N-channel JFET convention, \(V_{GS}\) is zero or negative.
N-channel vs P-channel JFET
| Feature | N-channel | P-channel |
|---|---|---|
| Channel | N-type | P-type |
| Gate regions | P-type | N-type |
| Majority carriers | Electrons | Holes |
| Usual gate polarity | Zero or negative relative to source | Opposite polarity |
| Current conduction | Mainly electrons | Mainly holes |
6. JFET operating regions
| Region | Behaviour |
|---|---|
| Ohmic or linear | At low \(V_{DS}\), drain current increases with drain voltage; channel behaves approximately like a controlled resistance. |
| Pinch-off or saturation | For fixed \(V_{GS}\), drain current becomes approximately constant as \(V_{DS}\) increases further. |
| Cutoff | Gate voltage is sufficiently reverse biased and drain current is approximately zero. |
| Breakdown | Excessive drain voltage causes a sharp rise in current; normal operation avoids this region. |
Very important distinction: Pinch-off does not mean zero drain current. Pinch-off marks the beginning of the approximately constant-current region. Cutoff is the condition where drain current becomes approximately zero.
7. JFET characteristics
Drain (output) characteristics
The drain characteristic shows the relationship between drain current \(I_D\) and drain-to-source voltage \(V_{DS}\) for different fixed values of gate-to-source voltage \(V_{GS}\).
- X-axis: \(V_{DS}\)
- Y-axis: \(I_D\)
- Each curve represents a different fixed \(V_{GS}\).
- For an N-channel JFET, making \(V_{GS}\) more negative reduces drain current.
- At \(V_{GS}=0\), saturation current is approximately \(I_{DSS}\).
Transfer characteristics
The transfer characteristic shows the relationship between drain current \(I_D\) and gate-to-source voltage \(V_{GS}\), usually in the saturation region.
For an idealised JFET, Shockley's equation is:
Where: - \(I_D\) = drain current - \(I_{DSS}\) = drain current at zero gate-to-source voltage in saturation - \(V_{GS}\) = applied gate-to-source voltage - \(V_{GS(off)}\) = cutoff gate-to-source voltage (negative for the usual N-channel convention)
Use the equation within the normal model range and with consistent voltage signs.
Solved numerical 1 — Find JFET drain current
Given: \(I_{DSS}=12\ mA\), \(V_{GS(off)}=-6\ V\), and \(V_{GS}=-2\ V\). Find \(I_D\).
Formula:
Substitution:
Solved numerical 2 — Find gate-to-source voltage
Given: \(I_{DSS}=10\ mA\), \(V_{GS(off)}=-5\ V\), and \(I_D=2.5\ mA\). Find \(V_{GS}\).
8. MOSFET construction and operation
A MOSFET has an insulated gate separated from the semiconductor by a thin insulating layer. Its main terminals are gate (G), drain (D), and source (S); a body or substrate terminal may also be present.
Because the gate is insulated, an ideal MOSFET draws no steady-state DC gate current. Real devices have small leakage, and the gate capacitance must be charged or discharged during switching.
Enhancement-mode MOSFET
An enhancement-mode MOSFET normally has no conducting channel at zero gate-to-source voltage.
For an N-channel enhancement MOSFET: 1. A positive gate-to-source voltage creates an electric field. 2. When the gate voltage reaches the threshold region, a conducting channel forms. 3. Increasing gate voltage beyond threshold generally strengthens the channel and allows more drain current, depending on the operating region.
For a P-channel enhancement MOSFET, voltage polarities and carrier types are reversed.
Depletion-mode MOSFET
A depletion-mode MOSFET has a conducting channel at zero gate-to-source voltage.
For an N-channel depletion MOSFET: - At \(V_{GS}=0\), drain current can flow. - A negative gate voltage depletes carriers and reduces channel current. - A sufficiently positive gate voltage can enhance channel conduction.
Enhancement vs depletion MOSFET
| Feature | Enhancement mode | Depletion mode |
|---|---|---|
| Channel at \(V_{GS}=0\) | Normally absent | Present |
| Normal state | Normally OFF | Normally ON |
| Gate action (N-channel) | Positive gate voltage creates/enhances channel | Negative gate voltage depletes channel |
| Channel polarity | N-channel or P-channel | N-channel or P-channel |
MOSFET output characteristics
The output characteristic is a graph of drain current \(I_D\) against drain-to-source voltage \(V_{DS}\) for different fixed gate voltages \(V_{GS}\).
For an enhancement-mode N-channel MOSFET, the main regions are:
- Cutoff: gate voltage is below the threshold condition; channel current is approximately zero.
- Ohmic/triode: channel behaves approximately like a voltage-controlled resistance.
- Saturation: in the ideal long-channel model, drain current is mainly controlled by gate overdrive voltage and changes less strongly with \(V_{DS}\).
Do not confuse MOSFET saturation with BJT saturation. MOSFET saturation is commonly used for amplification. BJT saturation is commonly used to represent a fully ON switch.
MOSFET transfer characteristic
The transfer characteristic shows how drain current changes with gate-to-source voltage under a specified drain-voltage condition.
For an enhancement-mode N-channel MOSFET, drain current begins to rise significantly when \(V_{GS}\) exceeds threshold voltage \(V_{TH}\).
A simplified long-channel saturation model is:
Where: - \(k\) = device-dependent parameter (definition varies by textbook) - \(V_{TH}\) = threshold voltage - \(V_{GS}-V_{TH}\) = gate overdrive voltage
This is an idealised model, not a universal equation for every MOSFET.
9. JFET vs MOSFET
| Feature | JFET | MOSFET |
|---|---|---|
| Gate structure | Reverse-biased P-N junction | Electrically insulated gate |
| Gate current | Very small | Ideally zero DC; small real leakage |
| Input resistance | High | Extremely high in normal operation |
| Types | N-channel and P-channel | N/P-channel, enhancement/depletion |
| Channel at zero gate voltage | Normally conducting | Depends on mode |
| Gate protection | Junction must be correctly biased | Gate can be sensitive to electrostatic discharge and excess voltage |
Practical note: Never exceed a MOSFET's maximum gate-voltage rating. Use appropriate electrostatic-discharge precautions when handling sensitive devices.
10. DC biasing of JFET
JFET biasing is the application of suitable DC voltages to establish a desired operating point (Q-point). For amplifier operation, a JFET is normally biased in its constant-current or saturation region.
Fixed gate bias
A separate gate supply establishes the required \(V_{GS}\). In a typical N-channel arrangement, the gate is negative relative to the source. The drain supply and drain resistor establish the drain circuit voltage.
Self-bias
Self-bias is a common JFET biasing method. A source resistor \(R_S\) is connected between source and ground, while the gate is connected to ground through a large resistor \(R_G\).
Since JFET gate current is approximately zero:
Source voltage:
Gate-to-source voltage:
For a grounded gate:
Drain voltage:
Drain-to-source voltage:
These expressions apply to the simple self-bias circuit where the same DC drain current flows through \(R_D\) and \(R_S\).
Solved numerical 3 — JFET self-bias
Given: \(I_D=2\ mA\), \(R_S=1\ k\Omega\), \(R_D=2\ k\Omega\), \(V_{DD}=12\ V\), and grounded gate. Find \(V_{GS}\) and \(V_{DS}\).
Step 1: Find source voltage
Step 2: Find gate-to-source voltage
Step 3: Find drain-to-source voltage
11. JFET Q-point
The JFET Q-point is the no-signal DC operating condition, commonly represented as:
- \(I_{DQ}\) = quiescent drain current
- \(V_{DSQ}\) = quiescent drain-to-source voltage
For amplification, choose a Q-point in the appropriate constant-current region and within the device's safe operating limits. A suitable Q-point allows the output to vary without entering cutoff, the ohmic region unintentionally, or breakdown.
12. Formula sheet
| Topic | Formula |
|---|---|
| JFET Shockley equation | \(I_D=I_{DSS}(1-V_{GS}/V_{GS(off)})^2\) |
| Self-bias gate voltage | \(V_{GS}\approx-I_D R_S\) |
| Source voltage | \(V_S=I_D R_S\) |
| Drain voltage | \(V_D=V_{DD}-I_D R_D\) |
| Drain-source voltage | \(V_{DS}=V_{DD}-I_D(R_D+R_S)\) |
| MOSFET gate overdrive | \(V_{OV}=V_{GS}-V_{TH}\) |
| Idealised MOSFET saturation model | \(I_D\approx\frac12 k(V_{GS}-V_{TH})^2\) |
13. Exam-ready short questions and answers
1. What does FET stand for? Field Effect Transistor.
2. Name the three main terminals of a FET. Gate, source and drain.
3. What are the two main types of FET? JFET and MOSFET.
4. Why is a FET called a unipolar device? Because channel conduction is mainly due to one type of majority carrier.
5. What is a JFET? A FET in which a reverse-biased gate-channel P-N junction controls channel current.
6. What is pinch-off in a JFET? The condition at which the channel becomes constricted near the drain and drain current becomes approximately constant for a fixed gate voltage.
7. Does pinch-off mean zero drain current? No. At pinch-off, current is approximately constant; at cutoff, current is approximately zero.
8. What is \(I_{DSS}\)? The JFET drain current at \(V_{GS}=0\) in the specified saturation condition.
9. What is \(V_{GS(off)}\)? The gate-to-source voltage at which JFET drain current becomes approximately zero under stated conditions.
10. What is a MOSFET? A FET with an insulated gate separated from the semiconductor by a thin insulating layer.
11. Name the two MOSFET operating modes. Enhancement mode and depletion mode.
12. What is self-bias in a JFET? A biasing method in which a source resistor develops source voltage and establishes the required gate-to-source voltage.
13. What is the JFET Q-point? The no-signal DC operating point, usually specified by \(I_{DQ}\) and \(V_{DSQ}\).
14. Descriptive questions for practice
- Define FET and explain its working principle.
- Classify FETs with a suitable diagram.
- Compare BJT and FET.
- Describe the construction and operation of an N-channel JFET.
- Explain the operation of a P-channel JFET.
- Explain the drain and transfer characteristics of a JFET.
- State and explain Shockley's equation for a JFET.
- Describe the construction and operation of an enhancement-mode MOSFET.
- Explain the operation of a depletion-mode MOSFET.
- Compare JFET and MOSFET.
- Explain JFET self-biasing with a circuit diagram and derive the expression for \(V_{GS}\).
- Define the JFET Q-point and explain its importance.
- Explain the output and transfer characteristics of an enhancement-mode MOSFET.
15. Numerical practice
Use the idealised Shockley equation for JFET questions unless stated otherwise.
Problem 1: An N-channel JFET has \(I_{DSS}=15\ mA\), \(V_{GS(off)}=-5\ V\), and \(V_{GS}=-1\ V\). Find \(I_D\).
Problem 2: An N-channel JFET has \(I_{DSS}=8\ mA\), \(V_{GS(off)}=-4\ V\), and \(I_D=2\ mA\). Find \(V_{GS}\).
Problem 3: A self-biased N-channel JFET has \(I_D=3\ mA\) and \(R_S=680\ \Omega\). Find \(V_{GS}\), assuming the gate is grounded.
Problem 4: A JFET self-bias circuit has \(V_{DD}=15\ V\), \(I_D=2\ mA\), \(R_D=3.3\ k\Omega\), and \(R_S=1\ k\Omega\). Find \(V_{DS}\).
Problem 5: An N-channel JFET has \(I_{DSS}=10\ mA\) and \(V_{GS(off)}=-5\ V\). Find drain current at \(V_{GS}=0\ V\) and at \(V_{GS}=-5\ V\).
Answer key
- \(I_D=15(1-(-1/-5))^2=15(0.8)^2=9.6\ mA\).
- \(\sqrt{2/8}=0.5=1-V_{GS}/(-4)\), so \(V_{GS}=-2\ V\).
- \(V_{GS}\approx-I_D R_S=-(0.003)(680)=-2.04\ V\).
- \(V_{DS}=15-0.002(3300+1000)=6.4\ V\).
- At \(V_{GS}=0\), \(I_D=I_{DSS}=10\ mA\). At \(V_{GS}=V_{GS(off)}=-5\ V\), \(I_D\approx0\).
16. Self-test
- What are the three main terminals of a FET?
- Which FET has a reverse-biased P-N junction at its gate?
- Which carriers mainly conduct in an N-channel JFET?
- What happens to N-channel JFET drain current when \(V_{GS}\) becomes more negative?
- What is the difference between pinch-off and cutoff?
- What is the function of the insulating layer in a MOSFET?
- What is the difference between enhancement and depletion MOSFET?
- What is the purpose of the source resistor in JFET self-bias?
- What quantities specify a JFET Q-point?
- Which MOSFET region is commonly used for linear amplification in the ideal long-channel model?
Answers
- Gate, source and drain.
- JFET.
- Electrons.
- Drain current decreases.
- Pinch-off begins the approximately constant-current region; cutoff makes channel current approximately zero.
- It electrically insulates the gate from the semiconductor.
- Enhancement mode normally has no channel at zero gate voltage; depletion mode has a channel at zero gate voltage.
- It develops source voltage and establishes negative \(V_{GS}\), helping set the operating point.
- \(I_{DQ}\) and \(V_{DSQ}\).
- Saturation region.
17. Common exam mistakes
- Calling the FET terminals emitter, base and collector. Correct: gate, source and drain.
- Saying a FET needs a large gate current. Its operation is controlled mainly by gate voltage.
- Mixing up JFET and MOSFET gate structures.
- Forgetting that an N-channel JFET normally uses zero or negative \(V_{GS}\).
- Saying pinch-off means zero drain current. Cutoff is the near-zero-current condition.
- Confusing MOSFET saturation with BJT saturation.
- Saying every MOSFET is normally OFF. Depletion-mode MOSFETs have a channel at zero gate voltage.
- Ignoring MOSFET gate-voltage ratings and ESD precautions.
- Forgetting the negative sign in \(V_{GS}\approx-I_D R_S\) for a grounded-gate N-channel self-bias circuit.
- Using Shockley's equation without checking the sign convention and stated operating range.
18. Last-minute revision checklist
- [ ] Define FET and name its terminals.
- [ ] Classify JFET and MOSFET.
- [ ] Compare BJT and FET.
- [ ] Draw and explain N-channel and P-channel JFET construction.
- [ ] Explain JFET operating regions and distinguish pinch-off from cutoff.
- [ ] Draw and explain drain and transfer characteristics.
- [ ] Memorise and apply Shockley's equation.
- [ ] Explain enhancement and depletion MOSFET operation.
- [ ] Compare JFET and MOSFET.
- [ ] Derive \(V_{GS}\approx-I_D R_S\) for JFET self-bias.
- [ ] Solve JFET current and self-bias numericals.
- [ ] Define the JFET Q-point.
Study sequence: First master the JFET construction and operating regions; then practise Shockley's equation; next learn MOSFET types and characteristics; finish with self-bias numericals and short-answer revision.